|
B/BV-A1 SW/SD/VS50 |
Wednesday, June 10, 2009
Sump Effluent Pumps
Special Purpose Models
HC20
Condensate Unit
HUP
Submersible utility pump - 1/6hp up to 20 gpm.
HPUSP125
Utility sink pump - 1/8hp up to 13 gpm.
HY106
FlexVane pump - Up to 5 gpm.
A+ Battery Back-Up Power Supply
The fully automatic power supply featurers Hydromatic's B-A1 or BV-A1 sump pump to continue operating when the battery is initiated, unlike most systems which rely on an extremely small, secondary pump.
Non Clog Dry Pit Pumps
First, the oil bath keeps the motor and bearings cool by dissipating heat and maintaining the correct operating temperature. The oil transfers heat generated in the motor windings to the housing where it is dissipated. Second, the oil bath locks out airborne moisture contamination which destroys motors and bearings. Air carries moisture that condenses with temperature changes and causes premature motor and bearing failure.
And, the oil bath permanently lubricates the bearings which minimizes heat and flushes contaminants away from bearing races. Heat and contaminants cause grease breakdown that leads to premature failure of grease-packed bearings supplied by other manufacturers. You get long pump life because the oil-filled motor dissipates heat from the windings, through the oil, to the outer housing.
Self Priming Pumps
Save Money with Peak Performance
The Hydromatic self primer series has external adjustments that allows you to easily maintain original operating efficiency and peak performance. By simply turning the external cap screws you easily adjust the clearance between the impeller and wear plate. You can make the external adjustment without disturbing the system. You don’t have to disassemble the pump and pipes. These external adjustment also allows you to quickly restore original efficiency and performance. External bolts move the bearing cap, which in turn moves the bearing and shaft assembly. This moves the impeller closer to the stationary wear plate for the proper clearance to restore peak performance and save money.
Dependable Operation
You get dependable pumping operation with the Hydromatic Dual Seal System. Two seals protect the bearings to give you longer pump life. We are aware of no other manufacturer that offers you this type of seal design for long-term, reliable pump service. The unique dual seal system incorporates an oil chamber which provides lubrication for the seals. The inboard seal offers protection because it “self-seals” tightly against the stationary face with pressure surges from the volute.
Hydromatic Pumps use Low Friction
Long-lasting John Crane Type 21 mechanical seals that you can obtain off-the-shelf worldwide. Tungsten Carbide seals are optional. The Hydromatic Dual Seal System offers you long, dependable pump operation. Click here to learn more.
New PFC6X6 Fiberglass Enclosed 6 Ft. by 6 Ft. Primer Lift Station.
Reliable 30MP, 30MPS and 30MMP Self Primer Pumps.
Reliable 40MP, 40MPH and 40MPS Self Primer Pumps.
New 40RP and 40RDP Self Primer Pumps.
New 60RP and 60RDP Self Primer Pumps.
Dependable 80MMP Self Primer Pump.
Dependable 100MMP Self Primer Pump.
Sewage Ejector Pumps
Hydromatic offers a complete product line of sewage pumps and complete packaged systems designed for the residential, commercial and industrial markets of the professional plumping trade.
SP40
Submersible sewage ejector pump - 4/10hp up to 120 gpm.
SP50
Submersible sewage ejector pump - 1/2hp up to 140 gpm.
SP50AB
Submersible sewage ejector pump - 1/2hp up to 140 gpm.
BV40
Submersible sewage ejector pump - 4/10hp up to 78 gpm.
SKV40
Submersible sewage ejector pump - 4/10hp up to 78 gpm.
SKV50
Submersible sewage ejector pump - 1/2hp up to 180 gpm.
SKHS50
Submersible sewage ejector pump - 1/2hp up to 140 gpm.
SKHS100
Submersible sewage ejector pump - 1hp up to 160 gpm.
SKHS150
Submersible sewage ejector pump - 1-1/2hp up to 155 gpm.
SKHS200
Submersible sewage ejector pump - 2hp up to 175 gpm.
SK50
Submersible sewage ejector pump - 1/2hp up to 120 gpm.
SK60
Submersible sewage ejector pump - 6/10hp up to 130 gpm.
SK75
Submersible sewage ejector pump - 3/4hp up to 150 gpm.
SK100
Submersible sewage ejector pump - 1hp up to 156 gpm.
S3S/SB3S
Submersible sewage ejector pump - 1.5hp - 3hp up to 375 gpm.
S4S/SB4S
Submersible sewage ejector pump - 3hp - 7.5hp up to 625 gpm.
HPGR
Submersible sewage grinder pump - 2hp up to 58 gpm.
Grinder Pump Systems
Hydromatic's complete grinder package is a proven, innovative solution to a changing world. The use of grinder pumps prove to be a superior solution that is cost effective and minimally disruptive to the natural environment. Submersible Grinder Pumps keep beauty in the environment and cash in the pocket.
A grinder pump based system can be installed using relatively small diameter piping (as small as 1-1/4 " to 2" laterals and mains), which can be laid in shallow trenches. Since the wastewater is pumped under low pressures, the piping can follow the terrain and be installed at minimal depths (just under the frost line in colder climates and according to local codes).
Cost savings come from the ability to eliminate costly deep excavation and through the use of small diameter pipe. Minimal excavation and soil disruption means that the beauty of any existing natural surrounding features can be saved.
TL-Pro System New!
A quality lift-out system available with your choice of a Hydromatic 2HP submersible rated grinder pump, the new Float Plus control panel, three weighted float switches and a fiberglass basin with anti-floatation collar. The Complete Grinder Package Offering is available with your choice of either HPG200, HPGR200 or HPGX submersible rated, centrifugal grinder pump.
TG-Pro System Improved!
A quality flex hose design system available with a choice of a Hydromatic 2HP submersible rated grinder pump, the new Float Plus control panel, three weighted float switches and a fiberglass basin with anti-floatation collar. The Complete Grinder Package Offering is available with your choice of either a HPG200 or HPGR200 centrifugal grinder pump or a HPD200 semi-positive displacement, submersible rated grinder pump.
EZ-Out System (for use with 2HP grinders only)
Complete firberglass basin with cover, and stainless steel upper guide rail bracket lifting chain. Available with your choice of Hydromatic's 2HP HPG200 or HPGR200 centrifugal grinder pump.
Hydro-Rail System (for use with 2HP grinders only)
Complete firberglass basin with cover, and stainless steel upper guide rail bracket lifting chain. Available with your choice of a Hydromatic vertical discharge grinder pump.
Hydromatic reserves the right to make revisions to its products and their specifications, this catalog and related information without notice. Most models are UL Listed and/or CSA Approved.
Effluent Pumps
Hydromatic offers a complete effluent pump product line designed for the residential, commercial and industrial markets of the professional plumping trade.
SHEF30
Submersible effluent pump - .30hp up to 44 gpm.
SHEF40
Submersible effluent pump - 4/10hp up to 33 gpm.
SHEF45 NEW!
Submersible effluent pump - 1/2hp up to 87 gpm.
SHEF50
Submersible effluent pump - 1/2hp up to 63 gpm.
SHEF100
Submersible effluent pump - 1hp up to 88 gpm.
OSP50
Submersible sump and effluent pump Up to 60 gpm
OSP50AB
Submersible sump and effluent pump Up to 60 gpm
SPD50
Submersible effluent pump - 1/2hp up to 112 gpm.
SPD100
Submersible effluent pump - 1hp up to 140 gpm.
SKHD150
Submersible effluent pump - 1-1/2hp up to 55 gpm.
SPX50
Submersible explosion proof effluent pump - 1/2hp up to 74 gpm.
SPX50H
Submersible high head explosion proof effluent pump - 1/2hp up to 74 gpm.
HE8-51, HE12-51, and HE20-51
Submersible effluent pumps - 1/2hp and 1-1/2hp up to 20 gpm
Effluent Pumps
Hydromatic offers a complete effluent pump product line designed for the residential, commercial and industrial markets of the professional plumping trade.
SHEF30
Submersible effluent pump - .30hp up to 44 gpm.
SHEF40
Submersible effluent pump - 4/10hp up to 33 gpm.
SHEF45 NEW!
Submersible effluent pump - 1/2hp up to 87 gpm.
SHEF50
Submersible effluent pump - 1/2hp up to 63 gpm.
SHEF100
Submersible effluent pump - 1hp up to 88 gpm.
OSP50
Submersible sump and effluent pump Up to 60 gpm
OSP50AB
Submersible sump and effluent pump Up to 60 gpm
SPD50
Submersible effluent pump - 1/2hp up to 112 gpm.
SPD100
Submersible effluent pump - 1hp up to 140 gpm.
SKHD150
Submersible effluent pump - 1-1/2hp up to 55 gpm.
SPX50
Submersible explosion proof effluent pump - 1/2hp up to 74 gpm.
SPX50H
Submersible high head explosion proof effluent pump - 1/2hp up to 74 gpm.
HE8-51, HE12-51, and HE20-51
Submersible effluent pumps - 1/2hp and 1-1/2hp up to 20 gpm
Grinder Pumps
Hydromatic grinder pumps offer you a field-proven, low cost solution to transport sewage and wastewater. Depending on the application Hydromatic offers both the centrifugal and the positive displacement grinder. Hydromatic also provides pre-packaged systems with everything included to meet your installation requirements. The basin piping from the home and tie-in point require only shallow trenches for installation, and the ground around the home is disrupted very little in the process.
Hydromatic grinders are ideal for residential, commercial, and resort applications. Used in low pressure sewer systems, the Hydromatic grinder offers a significant cost savings over conventional gravity-fed systems. You receive complete technical support and ongoing engineering assistance for the life of the pump. You can depend on Hydromatic grinders.
HPD Submersible positive displacement grinder pump.
Durable 2hp 1750 RPM, heads to 245 feet and flows of 19 gpm.
HPG Submersible centrifugal grinder pump.
Durable 2hp 3450 RPM, heads to 122 feet and flows of 62 gpm.
HPGR200 Submersible centrifugal grinder pump.
Durable 2HP 3450 RPM, heads to 105 feet and flows of 58 gpm.
HPGR200-D/HPGR200-D Retrofit Submersible centrifugal grinder pump.
Durable 2HP, heads to 105 feet and flows of 42 GPM, double-seal.
HPGF Submersible centrifugal grinder pump.
Durable 3-7.5hp 1750 RPM, heads to 108 feet and flows of 175 gpm.
HPGFH Submersible centrifugal grinder pump.
Durable 3-7.5hp 1750 RPM, heads to 108 feet and flows of 175 gpm.
HPGH Submersible centrifugal grinder pump.
Durable 3-7.5hp 3450 RPM, heads to 203 feet and flows of 120 gpm.
HPGHH Submersible centrifugal grinder pump.
Durable 3-7.5hp 3450 RPM, heads to 203 feet and flows of 120 gpm.
HPGX Submersible explosion proof grinder pump.
Durable 2hp 3450 RPM, heads to 100 feet and flows of 60.5 gpm.
HPGLX Submersible explosion proof grinder pump.
Durable 2hp 3450 RPM, heads to 60 feet and flows of 49 gpm.
HPGFX Submersible explosion proof grinder pump.
Durable 3-7.5hp 1750 RPM, heads to 108 feet and flows of 175 gpm.
HPGHX Submersible explosion proof grinder pump.
Durable 3-7.5hp 3450 RPM, heads to 203 feet and flows of 120 gpm.
PG Grinder pump.
Durable 2hp 3450 RPM, heads to 92.5 feet and flows of 42 gpm.
NPG Grinder pump.Durable 2hp 3450 RPM, heads to 92.5 feet and flows of 42gpm.
High Temp Pumps
For liquids up to 140 ºF, the SE-50 HT pump is a suitable selection. This model performs like a 1/3 HP pump, but offers a 1/2 HP motor - thus providing a 1.40 service factor. Internal motor heat is reduced, which compensates for higher liquid temperature.
For liquid temperatures of up to 190 ºF, Stancor offers high temperature stainless steel pumps for water (SSS-HT models) and sewage and wastewater (SS-HT models). All stainless steel HT models provide a service factor of 1.40-1.45 and include critical materials of construction that allow for intermittent 190º water temperatures. These include special motor insulation, silicon-carbide mechanical seals, Viton® oil seals, o-rings, gaskets and PVC jacketed cable. For applications where longer pumping cycles are necessary (more than 10 minutes at a time), special heat transfer oil can be added in the motor chamber so as to dissipate internal heat from the motor more rapidly (available with SS-HT series pumps).
Years of experience and sound engineering practices have produced high temperature pumps that stand up against demanding conditions and result in pumps that really do the job.
- All #316 stainless steel construction
- Silicon-Carbide vs. Silicon-Carbide mechanical seals
- Viton® o-rings, gaskets and oil seal
- PVC jacketed cable (33’)
- Thermally protected with auto-restart
- Guiderail Systems available
- Special heat transfer oil available for long pump cycle conditions
- Pumps from 1 HP 120/220 V (SS-100 HT) to 7.5 HP 230.460 V (SS-200 HT through SS-750 HT)
- Special voltages available upon request
- 1/2 HP 120/220/230/460 V
- Stainless steel motor housing
- Carbon vs Ceramic mechanical seals
- Buna o-rings and gaskets
- Thermally protected with auto-restart
- Up to 3/4" solids handling with Vortex clog-free impeller
- Built-in auto float switch available (single phase 115 V or 230 V)
- Guiderail systems available
- 1 HP 120/220/230/460 V
- All #304 stainless steel construction
- Silicon-Carbide vs Silicon-Carbide mechanical seals
- Viton® o-rings, gaskets and oil-seal
- PVC jacketed cable (50’)
- Thermally protected with auto-restart
- Built-in auto float switch available (single phase 115 V or 230 V)
- Compact design (14" high x 7.125" wide) with top discharge and double wall motor housing
SD 200
- High torque motor with large service factor
- Thermal overload protection
- Hardened stainless steel motor shaft
- Corrosion resistant 304 stainless steel motor housing (SD50 & SD75 series electro-chrome)
- Durable construction yet lightweight for easy portability
- Mechanical seals in seperate chamber with secondary lip seal; mechanical seals run in a separate oil-filled compartment, lip seal design prevents corrosives and solids infiltrating primary sealing unit
- Strainer provided for high efficiency and clog-free pumping
Applications:
- Telephone and utility transformer vaults
- Excavation & construction sites
- Basements
- Grain elevators
- Cooling towers
- Fire cleanup
- Other applicaitons requiring high volume water disposal
Optional Equipment:
- Automatic version available with piggy back float (up to 2 HP) or control panel and float
Stancor Avenger Series Pumps
MODEL SB-25
- Rugged fiber-reinforced thermal plastic body
- Non corrosive construction for long life
- Built-in discharge stand for stability and non-clog operation in sediment and sand
- Reliable sealing system
- Strong 1/4 HP motor with thermal overload protection
- Perfect for basement sump tanks
MODEL SB-12
- Super tough thermal molded pump body (Polypropylene) with a screened bottom inlet
- Mechanical and secondary lip seals, thermal overload protection for maximum motor life
- Fully corrosive resistant construction
- Compact and lightweight
- Pumps down within 1/10" of surface
- Great for basement and pool covers where sump is not available
- Complete with 1/2", 3/4" and 1" hose adapters
Optional Equipment:
- Automatic version available with piggy back float or built-in float
